$4.66
Add to Cart
Camaro 2016-20 MODE & Traction Control stab switch for center console. OEM. New!
SUMMARY
Brand new
-Has never been used in a vehicle
Don't pay $20+ for this part through GM
OEM factory original MODE & Traction control switch
Not a knock-off
Can be changed without removing console
-See DETAILS section
Wiring not included
-But a complete harness is available in another listing
--Message us with questions
Taken from an assembly line left-over console
Excellent condition
GM part number 23385718
30 day exchange-only warranty
Returns are not accepted
DETAILS
This MODE and traction control stab switch is brand new and has never been in a vehicle. It was removed from a brand new, assembly line leftover console. (We have the complete consoles available in other listings, as well as wiring harnesses and other parts. Please email if you have questions.) It is in excellent condition. It is GM part number 23385718. It lists for $20+ on the GM sites. If you're attempting to replace an existing module, make sure this matches your part number.
A wiring harness is required for use of this part. If you did not have the MODE-Traction switch previously, merely purchasing this switch may not get you up and running. The proper wiring harness may be required. We have one version of the harness in another listing. It will be up to you to install this switch and part of that installation may involve sourcing other parts.
This can be installed without completely removing your console. We have successfully removed one (from a semi-complete console) here from the top side. All it takes is a narrow, slim, rigid pry tool. (I used a plastic trim tool that was about 3/8" wide and very thin at the end.) First you have to remove the trim piece that goes around the switch. (And probably up on around the shifter. I'm not sure. That trim piece was not present on our console.) Then look at the new switch so you understand how the pressure tabs work that hold it in place, as well as where they are located. (They're approximately 1/2" wide and there's one on each side of the switch.) They must be depressed for it to pop out of position. Using the pry tool, you can get on the very top edge of each tab (one at a time) and push it in towards the switch. Pull up on the switch with your other hand when you get the tab pushed in. It should pop loose and you can move to the other side. It might take two or three tries but it can be done. (I did one here and had it out in less than a minute, and I had never removed one from the top before...) Again, looking at the new switch and seeing the pressure tabs will help you understand what to do and where to insert the pry tool on your existing switch.
APPLICATIONS
--Chevy Camaro: 2016-2020
SHIPPING, HANDLING & RETURNS
-Shipping cost is based on weight and zip code. This site does the figuring, not us. If you feel their calculation is high, you might be underestimating the package weight, size, and/or current shipping costs from our zip code (62401) to yours. Please don't ding us for shipping in the ratings, as we have no control over ever-increasing carrier rates.
-We will enter a tracking number into your order details here on the site.
They will email it to you if your notification preferences are set correctly.
-A signature is not typically required. If you are not home to receive the package, it will most likely be left at your door. Please monitor it's progress and arrange to collect it when it arrives.
-This site provides a section/tab in each ad for Shipping information.
We encourage you to check that section for prices, methods, time-frames, etc.
Brand new
-Has never been used in a vehicle
Don't pay $20+ for this part through GM
OEM factory original MODE & Traction control switch
Not a knock-off
Can be changed without removing console
-See DETAILS section
Wiring not included
-But a complete harness is available in another listing
--Message us with questions
Taken from an assembly line left-over console
Excellent condition
GM part number 23385718
30 day exchange-only warranty
Returns are not accepted
DETAILS
This MODE and traction control stab switch is brand new and has never been in a vehicle. It was removed from a brand new, assembly line leftover console. (We have the complete consoles available in other listings, as well as wiring harnesses and other parts. Please email if you have questions.) It is in excellent condition. It is GM part number 23385718. It lists for $20+ on the GM sites. If you're attempting to replace an existing module, make sure this matches your part number.
A wiring harness is required for use of this part. If you did not have the MODE-Traction switch previously, merely purchasing this switch may not get you up and running. The proper wiring harness may be required. We have one version of the harness in another listing. It will be up to you to install this switch and part of that installation may involve sourcing other parts.
This can be installed without completely removing your console. We have successfully removed one (from a semi-complete console) here from the top side. All it takes is a narrow, slim, rigid pry tool. (I used a plastic trim tool that was about 3/8" wide and very thin at the end.) First you have to remove the trim piece that goes around the switch. (And probably up on around the shifter. I'm not sure. That trim piece was not present on our console.) Then look at the new switch so you understand how the pressure tabs work that hold it in place, as well as where they are located. (They're approximately 1/2" wide and there's one on each side of the switch.) They must be depressed for it to pop out of position. Using the pry tool, you can get on the very top edge of each tab (one at a time) and push it in towards the switch. Pull up on the switch with your other hand when you get the tab pushed in. It should pop loose and you can move to the other side. It might take two or three tries but it can be done. (I did one here and had it out in less than a minute, and I had never removed one from the top before...) Again, looking at the new switch and seeing the pressure tabs will help you understand what to do and where to insert the pry tool on your existing switch.
APPLICATIONS
--Chevy Camaro: 2016-2020
SHIPPING, HANDLING & RETURNS
-Shipping cost is based on weight and zip code. This site does the figuring, not us. If you feel their calculation is high, you might be underestimating the package weight, size, and/or current shipping costs from our zip code (62401) to yours. Please don't ding us for shipping in the ratings, as we have no control over ever-increasing carrier rates.
-We will enter a tracking number into your order details here on the site.
They will email it to you if your notification preferences are set correctly.
-A signature is not typically required. If you are not home to receive the package, it will most likely be left at your door. Please monitor it's progress and arrange to collect it when it arrives.
-This site provides a section/tab in each ad for Shipping information.
We encourage you to check that section for prices, methods, time-frames, etc.
